diff options
Diffstat (limited to 'mail-filter/opendkim/files/opendkim-2.10.3-openrc.patch')
| -rw-r--r-- | mail-filter/opendkim/files/opendkim-2.10.3-openrc.patch | 303 |
1 files changed, 303 insertions, 0 deletions
diff --git a/mail-filter/opendkim/files/opendkim-2.10.3-openrc.patch b/mail-filter/opendkim/files/opendkim-2.10.3-openrc.patch new file mode 100644 index 000000000000..9033b84281ca --- /dev/null +++ b/mail-filter/opendkim/files/opendkim-2.10.3-openrc.patch @@ -0,0 +1,303 @@ +diff --git a/Makefile.am b/Makefile.am +index ee2d21ab..b085b988 100644 +--- a/Makefile.am ++++ b/Makefile.am +@@ -39,6 +39,52 @@ DISTCLEANFILES = opendkim-@VERSION@.tar.gz + # though. + DISTCHECK_CONFIGURE_FLAGS=--enable-vbr --with-lua --enable-stats --with-odbx --with-db --with-openssl=/usr/local --enable-atps --enable-replace_rules + ++ ++# ++# Handle some scripts and configuration files that need @VARIABLE@ ++# replacements here, so that we can share the rules (which are ++# identical) between all of the targets. ++# ++ ++# We want to *build and install* these on the target machine. ++nodist_doc_DATA = contrib/OpenRC/opendkim.openrc \ ++ contrib/systemd/opendkim.service \ ++ contrib/systemd/opendkim.tmpfiles \ ++ opendkim/opendkim.conf.simple \ ++ opendkim/opendkim.conf.simple-verify ++ ++# Custom variable to keep the rule below as sane as possible. ++doc_DATA_intermediate = contrib/OpenRC/opendkim.openrc.in ++ ++# We want to *ship* these. ++EXTRA_DIST = contrib/OpenRC/opendkim.openrc.in.in \ ++ contrib/systemd/opendkim.service.in \ ++ contrib/systemd/opendkim.tmpfiles.in \ ++ opendkim/opendkim.conf.simple.in \ ++ opendkim/opendkim.conf.simple-verify.in ++ ++# The next rule allow us to replace bindir, libdir, etc. within ++# files. The example is taken from the autoconf documentation and can ++# be found in the "Installation Directory Variables" section. ++edit = sed -e 's|@DOMAIN[@]|$(DOMAIN)|g' \ ++ -e 's|@RUNSTATEDIR[@]|$(runstatedir)|g' \ ++ -e 's|@SBINDIR[@]|$(sbindir)|g' \ ++ -e 's|@SYSCONFDIR[@]|$(sysconfdir)|g' ++ ++# This rule includes EVERY source/intermediate file as a dependency of ++# EVERY output file, which is clearly wrong, but it may be the best we ++# can do without duplication. At least it's the right kind of wrong, ++# and rebuilds too often rather than not often enough. ++$(nodist_doc_DATA): $(doc_DATA_intermediate) $(EXTRA_DIST) Makefile ++ rm -f $@ $@.tmp ++ srcdir=''; \ ++ test -f ./$@.in || srcdir=$(srcdir)/; \ ++ $(edit) $${srcdir}$@.in > $@.tmp ++ mv $@.tmp $@ ++ ++ ++ ++ + $(DIST_ARCHIVES): distcheck + + $(DIST_ARCHIVES).md5: $(DIST_ARCHIVES) +diff --git a/configure.ac b/configure.ac +index 76914fd9..a478bb83 100644 +--- a/configure.ac ++++ b/configure.ac +@@ -65,6 +65,9 @@ AC_PROG_CC_C99 + AM_PROG_CC_C_O + AC_PROG_LIBTOOL + ++# Used by the OpenRC service script, at least. ++AC_PROG_GREP ++ + PKG_PROG_PKG_CONFIG + + # +@@ -2628,6 +2631,11 @@ AC_SUBST(SPECCONFIGURE) + AC_SUBST(SPECREQUIRES) + AC_SUBST(SPECBUILDREQUIRES) + ++# Autoconf 2.70 will support this, and many distros patch it in, ++# but Autoconf 2.70 hasn't actually been released yet. ++AS_IF([test -z "${runstatedir}"], [runstatedir='${localstatedir}/run']) ++AC_SUBST([runstatedir]) ++ + # + # Finish up + # +@@ -2639,6 +2647,7 @@ AC_OUTPUT([ Makefile + contrib/docs/Makefile + contrib/init/Makefile + contrib/init/generic/Makefile ++ contrib/OpenRC/opendkim.openrc.in + contrib/init/redhat/Makefile + contrib/init/redhat/opendkim + contrib/init/redhat/opendkim-default-keygen +@@ -2650,8 +2659,6 @@ AC_OUTPUT([ Makefile + contrib/spec/Makefile + contrib/spec/opendkim.spec + contrib/stats/Makefile +- contrib/systemd/Makefile +- contrib/systemd/opendkim.service + libopendkim/opendkim.pc libopendkim/Makefile + libopendkim/docs/Makefile + libopendkim/tests/Makefile +@@ -2664,8 +2671,6 @@ AC_OUTPUT([ Makefile + opendkim/opendkim-lua.3 + opendkim/opendkim-testkey.8 opendkim/opendkim-stats.8 + opendkim/opendkim-testmsg.8 opendkim/opendkim.conf.5 +- opendkim/opendkim.conf.simple +- opendkim/opendkim.conf.simple-verify + opendkim/opendkim-atpszone.8 opendkim/opendkim-spam.1 + opendkim/tests/Makefile + stats/Makefile stats/opendkim-importstats.8 +diff --git a/contrib/Makefile.am b/contrib/Makefile.am +index 76df01cd..401130bb 100644 +--- a/contrib/Makefile.am ++++ b/contrib/Makefile.am +@@ -3,6 +3,6 @@ + + #AUTOMAKE_OPTIONS = foreign + +-SUBDIRS = convert docs init ldap lua patches repute spec stats systemd ++SUBDIRS = convert docs init ldap lua patches repute spec stats + + dist_doc_DATA = README +diff --git a/contrib/OpenRC/.gitignore b/contrib/OpenRC/.gitignore +new file mode 100644 +index 00000000..af0aa700 +--- /dev/null ++++ b/contrib/OpenRC/.gitignore +@@ -0,0 +1,2 @@ ++opendkim.openrc ++opendkim.openrc.in +diff --git a/contrib/OpenRC/opendkim.openrc.in.in b/contrib/OpenRC/opendkim.openrc.in.in +new file mode 100644 +index 00000000..d9631cdf +--- /dev/null ++++ b/contrib/OpenRC/opendkim.openrc.in.in +@@ -0,0 +1,54 @@ ++#!/sbin/openrc-run ++# Copyright 1999-2019 Gentoo Authors ++# Distributed under the terms of the GNU General Public License v2 ++ ++CONFFILE="@SYSCONFDIR@/opendkim/${RC_SVCNAME}.conf" ++required_files="${CONFFILE}" ++ ++command="@SBINDIR@/opendkim" ++pidfile="@RUNSTATEDIR@/${RC_SVCNAME}.pid" ++command_args="-P ${pidfile} -x ${CONFFILE}" ++extra_commands="checkconfig" ++ ++depend() { ++ use dns logger net ++ before mta ++} ++ ++checkconfig() { ++ # ++ # The opendkim.conf man page says, ++ # ++ # For parameters that are Boolean in nature, only the first byte ++ # of the value is processed... For negative values, the following ++ # are accepted: "F", "f", "N", "n", "0".' ++ # ++ if @GREP@ '^[[:space:]]*Background[[:space:]]\+[FfNn0]' "${CONFFILE}" \ ++ >/dev/null 2>&1; then ++ eend 1 "${RC_SVCNAME} cannot run in the foreground!" ++ fi ++ if ! "${command}" -n "${command_args}"; then ++ eend 1 "${RC_SVCNAME} configuration check failed" ++ fi ++} ++ ++start_pre() { ++ # If this isn't a restart, make sure that the user's config isn't ++ # busted before we try to start the daemon (this will produce ++ # better error messages than if we just try to start it blindly). ++ # ++ # If, on the other hand, this *is* a restart, then the stop_pre ++ # action will have ensured that the config is usable and we don't ++ # need to do that again. ++ if [ "${RC_CMD}" != "restart" ]; then ++ checkconfig || return $? ++ fi ++} ++ ++stop_pre() { ++ # If this is a restart, check to make sure the user's config ++ # isn't busted before we stop the running daemon. ++ if [ "${RC_CMD}" = "restart" ]; then ++ checkconfig || return $? ++ fi ++} +diff --git a/contrib/systemd/Makefile.am b/contrib/systemd/Makefile.am +deleted file mode 100644 +index 2ffc88cc..00000000 +--- a/contrib/systemd/Makefile.am ++++ /dev/null +@@ -1,3 +0,0 @@ +-# Copyright (c) 2013, The Trusted Domain Project. All rights reserved. +- +-dist_doc_DATA = opendkim.service +diff --git a/contrib/systemd/opendkim.service.in b/contrib/systemd/opendkim.service.in +index f7665f43..236f8a06 100644 +--- a/contrib/systemd/opendkim.service.in ++++ b/contrib/systemd/opendkim.service.in +@@ -1,20 +1,28 @@ +-# If you are using OpenDKIM with SQL datasets it might be necessary to start OpenDKIM after the database servers. +-# For example, if using both MariaDB and PostgreSQL, change "After=" in the "[Unit]" section to: +-# After=network.target nss-lookup.target syslog.target mariadb.service postgresql.service ++# If you are using OpenDKIM with SQL datasets, you should start ++# OpenDKIM after your database server. For example, when using ++# PostgreSQL, you should create a supplementary ".conf" file in the ++# appropriate directory containing, ++# ++# [Unit] ++# After=postgresql.service ++# + + [Unit] + Description=DomainKeys Identified Mail (DKIM) Milter +-Documentation=man:opendkim(8) man:opendkim.conf(5) man:opendkim-genkey(8) man:opendkim-genzone(8) man:opendkim-testadsp(8) man:opendkim-testkey http://www.opendkim.org/docs.html ++Documentation=man:opendkim(8) \ ++ man:opendkim.conf(5) \ ++ man:opendkim-genkey(8) \ ++ man:opendkim-genzone(8) \ ++ man:opendkim-testkey(8) \ ++ http://www.opendkim.org/docs.html + After=network.target nss-lookup.target syslog.target + + [Service] + Type=forking +-PIDFile=@localstatedir@/run/opendkim/opendkim.pid +-EnvironmentFile=-@sysconfdir@/sysconfig/opendkim +-ExecStart=@sbindir@/opendkim $OPTIONS ++ExecStart=@SBINDIR@/opendkim -P @RUNSTATEDIR@/opendkim.pid ++ExecStartPre=@SBINDIR@/opendkim -P @RUNSTATEDIR@/opendkim.pid -n -f + ExecReload=/bin/kill -USR1 $MAINPID +-User=opendkim +-Group=opendkim ++PIDFile=@RUNSTATEDIR@/opendkim.pid + + [Install] + WantedBy=multi-user.target +diff --git a/contrib/systemd/opendkim.tmpfiles.in b/contrib/systemd/opendkim.tmpfiles.in +new file mode 100644 +index 00000000..a9118974 +--- /dev/null ++++ b/contrib/systemd/opendkim.tmpfiles.in +@@ -0,0 +1,5 @@ ++# We allow everyone to read/traverse this directory because if it ++# contains a local socket, then (for example) your MTA will want to ++# look in there. Permissions on the socket itself are controlled ++# by the "UserID" and "UMask" directives in the daemon's configuration. ++d @RUNSTATEDIR@/opendkim 0755 opendkim opendkim +diff --git a/opendkim/Makefile.am b/opendkim/Makefile.am +index 4aa615c1..7d514771 100644 +--- a/opendkim/Makefile.am ++++ b/opendkim/Makefile.am +@@ -16,9 +16,11 @@ endif + sbin_PROGRAMS += opendkim-stats + endif + ++ + dist_sbin_SCRIPTS = opendkim-genkey +-dist_doc_DATA = opendkim.conf.sample opendkim.conf.simple \ +- opendkim.conf.simple-verify README.SQL ++ ++dist_doc_DATA = opendkim.conf.sample README.SQL ++ + + if BUILD_FILTER + sbin_PROGRAMS += opendkim +diff --git a/opendkim/opendkim.conf.simple-verify.in b/opendkim/opendkim.conf.simple-verify.in +index 2224b64f..463048ab 100644 +--- a/opendkim/opendkim.conf.simple-verify.in ++++ b/opendkim/opendkim.conf.simple-verify.in +@@ -17,5 +17,5 @@ Mode v + + # ADSPDiscard no + +-# PidFile /var/run/opendkim/opendkim.pid ++# PidFile @RUNSTATEDIR@/opendkim.pid + +diff --git a/opendkim/opendkim.conf.simple.in b/opendkim/opendkim.conf.simple.in +index 735b924b..b70bfb46 100644 +--- a/opendkim/opendkim.conf.simple.in ++++ b/opendkim/opendkim.conf.simple.in +@@ -12,6 +12,12 @@ KeyFile /var/db/dkim/@DOMAIN@.private + + Socket inet:8891@localhost + ++# To use a local socket instead, specify a path here. The "standard" ++# location is under @runstatedir@/opendkim, and it's best to agree ++# on that directory so that various init systems can configure its ++# permissions and ownership automatically. ++#Socket local:@RUNSTATEDIR@/opendkim/opendkim.sock ++ + ReportAddress postmaster@@DOMAIN@ + SendReports yes + +@@ -25,4 +31,4 @@ SendReports yes + # + # PeerList X.X.X.X + +-# PidFile /var/run/opendkim/opendkim.pid ++# PidFile @RUNSTATEDIR@/opendkim.pid |